Lab guide · Testing
How to Read a Peptide COA: 9-Step Checklist (2026 Guide)
How to read a peptide COA step by step: what each section means, how to judge HPLC purity and mass spec identity, why net content matters, and how to spot and verify a fake report.
Key takeaways
- Only trust a COA that is batch-specific, from an independent lab, and verifiable with that lab.
- HPLC shows purity; mass spectrometry confirms identity. A good COA has both.
- Purity, quantity and net peptide content are three different numbers.
- Missing chromatograms, mismatched batch numbers and reports you can’t verify are red flags.
What is a peptide COA?
A peptide COA (certificate of analysis) is a laboratory report that records the test results for one specific production batch of a peptide: which tests were run, which methods were used, the results and the date. Knowing how to read a peptide COA is the only reliable way to judge a supplier, because the COA is the one document that describes what is actually in the vial rather than what the label claims.
For research peptides, two results carry most of the weight: HPLC purity, which shows how clean the sample is, and mass spectrometry, which confirms it is the right molecule. A good COA adds a measured quantity per vial and states clearly which optional tests were not performed.
Why it matters: when a Ghent University group re-tested commercially supplied research peptides ordered at 95%+ purity, only 44% met the purity stated on the supplier’s COA, and one sample was a different structure altogether (Verbeke et al., 2015).
How to read a peptide COA in 9 steps
This is how to read a peptide COA from any supplier, in the order that catches problems fastest. Each step is explained in more detail further down.
- Check who did the testing. The lab named on the report should be independent of the seller. A COA issued by the supplier itself is a self-assessment, not third-party testing.
- Match the compound and amount. The sample name and stated amount (e.g. BPC-157, 10 mg) should match the product you are ordering exactly.
- Match the batch number. The batch or lot number on the report must match the number on your vial or order confirmation. No batch number, no traceability.
- Check the dates. The test date should be recent and after the batch was made. A report years older than the current stock describes a different batch.
- Read the HPLC purity. Look for 98-99%+ for research-grade peptides, and look at the chromatogram itself: one dominant, sharp peak.
- Confirm identity by mass spec. The observed mass should match the theoretical molecular weight of the peptide within a small tolerance.
- Check the quantity. If the lab measured mg per vial, compare it with the label. Purity and quantity are separate results.
- Note what was not tested. Endotoxin, sterility, heavy metals and counter-ion content are optional extras. “Not tested” is honest; a missing line is not.
- Verify the report with the lab. Use the task number or verification key to confirm the report exists in the lab’s own records.
If a report fails steps 1, 3 or 9, the rest of the numbers don’t matter: you cannot connect the result to the vial you are buying.
Peptide COA example: an annotated walkthrough
Layouts vary between labs, but the same building blocks appear on almost every report. The example below is illustrative (not a real batch), and the numbers match the checklist above, so you can see how to read a peptide COA field by field.
| # | Field | What a good result looks like |
|---|---|---|
| 1 | Lab name and report ID | A named, independent lab and a unique task or report number. |
| 2 | Sample | Exact compound and amount, e.g. BPC-157 10 mg. |
| 3 | Batch / lot | Identical to the number on your vial or order. |
| 4 | Dates | Received and tested dates that make sense for current stock. |
| 5 | Purity (HPLC) | 98-99%+, with the chromatogram and method (column, wavelength) shown. |
| 6 | Identity (MS) | Observed mass within tolerance of the expected mass. |
| 7 | Quantity | Measured mg per vial close to the label. |
| 8 | Not tested | Optional tests clearly marked as not performed. |
| 9 | Verification | A key or task number you can check with the lab. |
HPLC purity: how to read the chromatogram
High-performance liquid chromatography (HPLC) pushes the dissolved sample through a packed column, usually reversed-phase C18. Different components leave the column at different times and a UV detector (typically 214-220 nm, where the peptide bond absorbs) records each one as a peak.
For a deeper look at the method, see HPLC peptide testing explained.
How the purity percentage is calculated
Purity is the area of the main peak divided by the area of all peaks. If the main peak is 99.1% of the total area, the batch is reported as 99.1% pure. The remaining fraction is related impurities: deletion and truncated sequences, incompletely deprotected chains and other by-products of solid-phase synthesis, all of which are catalogued in this review of peptide impurities.
What a trustworthy chromatogram looks like
- One tall, sharp main peak with a clean baseline either side.
- Any other peaks small and clearly separated from the main one.
- Labelled axes, a retention time for the main peak and the method stated somewhere on the report.
Watch for: a purity number with no chromatogram, or a chromatogram with no axes. The graph is the evidence; the percentage on its own is only a claim.
One limit to keep in mind: HPLC can only separate what the method can resolve. An impurity that comes off the column at the same time as the main peak is counted as “pure”, which is one more reason identity has to be confirmed separately.
Mass spectrometry: confirming the peptide is what it says
Mass spectrometry (MS) measures the mass of the molecules in the sample. Every peptide has a theoretical molecular weight fixed by its sequence, so a good peptide COA shows the observed mass next to the expected one.
Reading m/z and charge states
Electrospray ionisation gives peptides several charges, so the raw spectrum shows peaks at mass-to-charge (m/z) values rather than one number. For example, BPC-157 has a molecular weight of about 1419.5 Da; with two extra protons ([M+2H]2+) it appears near m/z 710.8. Labs usually deconvolute these peaks into one molecular mass, which is the figure to compare.
Coupling LC with even a simple single-quad MS detector lets a lab identify the main compound and small impurities directly, as this Ghent University QC study shows. A match within tolerance confirms identity; a clear mismatch means the sample is something else, however pure it is.
Net peptide content vs. purity
This is the most misunderstood line on a peptide COA. Purity describes how much of the peptide material is the target sequence. Net peptide content describes how much of the powder in the vial is peptide at all, because lyophilised peptides also contain counter-ions and residual water.
| Measurement | Answers | Typical method |
|---|---|---|
| HPLC purity | Is the peptide clean? | Reversed-phase HPLC-UV |
| Identity | Is it the right molecule? | LC-MS / ESI-MS |
| Quantity | How many mg of peptide are in the vial? | HPLC against a reference standard |
| Net peptide content | What share of the powder is peptide? | Amino acid analysis or nitrogen (CHN) analysis |
| Water content | How much moisture is present? | Karl Fischer titration |
Worked example
A vial contains 10 mg of powder. Net peptide content is 80% and HPLC purity is 99%. The amount of target peptide is 10 × 0.80 × 0.99 = 7.92 mg. That is why a measured quantity per vial is so useful: it answers the practical question directly. Try the numbers yourself with our net peptide content calculator.
Lab note: a small variance from the label is normal for milligram fills. A vial that tests far below its stated amount is a quality problem even when purity is excellent.
Counter-ions: TFA vs. acetate
Peptides purified by reversed-phase HPLC usually leave synthesis as trifluoroacetate (TFA) salts. Some suppliers exchange them for acetate or hydrochloride. The counter-ion adds weight that isn’t peptide (one reason net content is below 100%), and residual TFA can interfere with some cell-based assays. If the salt form matters for your work, ask whether it was measured; most standard research COAs don’t report it.
Endotoxin, sterility and heavy metals
These are optional tests and most research-peptide COAs don’t include them. When they are reported, this is what they mean:
- Endotoxin: measured with the LAL test (Ph. Eur. 2.6.14 / USP <85>), reported in EU per mg.
- Sterility: a culture test for microbial growth (Ph. Eur. 2.6.1).
- Heavy metals: elemental analysis, usually ICP-MS, for lead, cadmium, arsenic and mercury.
A trustworthy report says “not tested” for anything it didn’t cover. A report that implies safety testing without showing a result should be treated as unverified.
Batch numbers, dates and traceability
Traceability is what turns a lab result into evidence about your vial. Check three things: the batch number on the report matches your vial, the test date fits the age of the stock, and each new batch gets a new report. A single report reused across months of stock, or across several products, tells you nothing about what ships today.
At Baltic Peptides every batch is listed on our COA page, and support can confirm which batch an order came from. Wholesale buyers receive the same batch reports with every bulk order.
Is the testing lab independent and accredited?
The strongest COAs come from a lab with no stake in the result. Look for the lab’s full name and address, a report ID, and a way to contact the lab directly. ISO/IEC 17025 is the international accreditation standard for testing labs; if a supplier claims it, the lab’s accreditation certificate and scope should be easy to find.
Our batches are tested by Janoshik Analytical, an independent lab in the Czech Republic that issues every report with a unique task number. You can read more about how we work with our lab.
How to spot a fake or edited peptide COA
- No lab name, or the “lab” is the seller itself.
- No batch number, or one that doesn’t match your vial.
- The same report used for several products, or for months of stock.
- A purity figure with no chromatogram, or a chromatogram with no axes or retention time.
- No mass spectrometry result, so identity is never confirmed.
- Fonts, alignment or sharpness that change around the numbers, a classic sign of editing.
- Suspiciously round results everywhere (exactly 99.00%).
- A report that can’t be found when you check it with the lab.
How to verify a peptide COA with the lab
- Find the lab name and the task number or verification key on the report.
- Go to the lab’s own website (type the address yourself rather than following a link in the PDF).
- Enter the key or contact the lab with the task number.
- Compare the lab’s record with the report: sample name, batch, date and results should be identical.
If the record doesn’t exist or doesn’t match, treat the report as unverified, whatever it says.
Reading COAs when buying peptides in Europe
Knowing how to read a peptide COA matters even more when you order across borders. For researchers in the EU, two practical points help. First, ask for the batch COA before ordering, not after: a supplier with current, batch-specific reports can send them immediately. Second, an EU-based supplier testing with an EU lab keeps the whole chain inside one customs area, so the batch that was tested is the batch that ships, without relabelling or re-packing in transit. Our shipping page covers delivery times across the EU, and the FAQ answers the most common questions about batches and testing.
Common mistakes when reading a peptide COA
Most errors come from reading one number in isolation. These are the ones we see most often in questions from researchers:
- Treating purity as quantity. A 99% purity result says nothing about how many milligrams are in the vial. Look for a separate quantity or net content result.
- Ignoring the batch number. A perfect report for a different batch is irrelevant to the vial on your bench.
- Accepting identity without data. “Identity: conforms” with no observed mass is a statement, not a measurement.
- Comparing purity across different methods. Results from different columns, gradients or wavelengths are not always directly comparable. Compare like with like.
- Assuming optional tests were done. If endotoxin or sterility results are not printed, they were not tested.
- Trusting a screenshot. A cropped image of a report can hide the batch number, date or lab. Ask for the full PDF.
Questions to ask a supplier about their COA
A reliable supplier can answer all of these in one reply. If they can’t, that tells you something too.
- Which independent lab tested this batch, and what is the task number?
- Does the batch number on the report match the vials currently shipping?
- Was quantity per vial measured, or only purity?
- Is there a mass spectrometry result with the observed mass?
- Were any optional tests (endotoxin, sterility, heavy metals) performed?
- How often are batches re-tested, and are older reports kept online?
You can ask us any of these through our support team, or check the COA archive directly.
How to read a peptide COA: the short version
If you remember one thing about how to read a peptide COA, make it this: a report is only as good as its link to your vial. Check the lab, the batch and the verification first; then read purity, identity and quantity as three separate answers to three separate questions. A supplier who makes all of that easy to check, for every batch, is a supplier worth working with.
Sources and further reading
- Verbeke F. et al. (2015). Quality evaluation of synthetic quorum sensing peptides used in R&D. J Pharm Anal 5(3):169-181. PMC
- D’Hondt M. et al. (2014). Related impurities in peptide medicines. J Pharm Biomed Anal 101:2-30. PubMed
- D’Hondt M. et al. (2016). Implementation of a single quad MS detector in routine QC analysis of peptide drugs. J Pharm Anal 6(1):24-31. PMC
- ICH Q6B: Specifications for biotechnological/biological products. European Medicines Agency
- ISO/IEC 17025: General requirements for the competence of testing and calibration laboratories. ISO
All Baltic Peptides products are supplied strictly for laboratory research use. They are not medicines, supplements or food and are not for human or animal use. This article explains analytical testing and is for educational purposes only.
FAQ
Common questions
What is a COA for peptides?
How do you read a peptide COA quickly?
What purity should a research peptide have?
Is HPLC enough to prove a peptide is genuine?
What is the difference between purity and net peptide content?
Why is my vial slightly different from the label?
Do research peptide COAs include endotoxin testing?
How can I tell if a COA is fake?
What does “verification key” mean on a COA?
Where can I see Baltic Peptides COAs?
Keep reading
Related reading
HPLC peptide testing explained
How HPLC purity is measured and how to read a chromatogram.
Net peptide content explained
Why a 10 mg vial is not 10 mg of peptide, with a calculator.
How to store peptides in the lab
Keep lyophilised and reconstituted peptides stable in the lab.
See the COA for the batch you’re ordering
Every Baltic Peptides batch is tested independently and published in full, before it ships.
