Lab guide · Testing
HPLC Peptide Testing Explained: Purity, Chromatograms & What the Numbers Mean
HPLC peptide testing is behind every purity figure on a COA. Here is how the method works, how to read a chromatogram, what the percentage really measures, and why it needs a mass spec result alongside it.
Key takeaways
- HPLC measures purity as the main peak’s share of total UV peak area.
- It cannot confirm identity: that needs mass spectrometry.
- Water and counter-ions are invisible to the detector, so purity is not peptide content.
- Compare purity results only when methods are similar and the full chromatogram is shown.
What is HPLC peptide testing?
HPLC peptide testing is the standard way to measure how pure a synthetic peptide is. High-performance liquid chromatography separates a dissolved sample into its components and measures each one, so the lab can report what share of the material is the target peptide and what share is something else. Almost every research-peptide certificate of analysis leads with an HPLC result, which is why understanding it is the first step in reading a peptide COA.
It is also the method manufacturers use to purify peptides in the first place. Bachem describes reversed-phase HPLC on C18 silica with UV detection as the standard method for peptide purification, followed by analytical HPLC to confirm the result.
In one sentence: HPLC tells you how clean a peptide sample is. It does not, on its own, prove the sample is the right peptide; that is the job of mass spectrometry.
How HPLC works, step by step
- Dissolve. A small amount of the peptide is dissolved, usually in water with a little acetonitrile or acid.
- Inject. A few microlitres go into a stream of liquid (the mobile phase).
- Separate. The stream passes through a column packed with C18-coated silica. More hydrophobic molecules stick longer; more polar ones come out sooner.
- Gradient. The share of organic solvent (acetonitrile) rises over the run, pushing progressively stickier molecules off the column.
- Detect. A UV detector records absorbance at around 214-220 nm, where the peptide bond absorbs, and draws each component as a peak.
- Integrate. Software measures the area of every peak; purity is the main peak’s share of the total.
The mobile phase almost always contains 0.1% trifluoroacetic acid (TFA), which sharpens peptide peaks. That is also why most research peptides end up as TFA salts, a point covered in our guide to net peptide content.
How to read an HPLC chromatogram
The chromatogram is the graph that proves the purity number, and it is the part of HPLC peptide testing most people skip. Retention time runs along the bottom; detector signal runs up the side. Four things to look at:
- The main peak should be tall, narrow and symmetrical, and clearly dominate the trace.
- Secondary peaks should be small and well separated. Their areas add up to the impurity percentage.
- Shoulders on the main peak suggest an impurity that is not fully separated.
- The baseline should be flat. A rising or noisy baseline makes small peaks hard to integrate fairly.
How the purity percentage is calculated
Purity is reported as area percent: the main peak’s area divided by the total area of all integrated peaks. A main peak of 98.7 area units out of 100 gives 98.7% purity. Because it is a ratio, the same sample injected at a different concentration should give a similar percentage.
What HPLC can and can’t tell you
HPLC peptide testing is powerful, but it has blind spots worth knowing:
| HPLC shows | HPLC does not show |
|---|---|
| Share of UV-absorbing material that is the main component | Whether the main component is the right sequence |
| Number and size of related impurities | Impurities that co-elute exactly with the main peak |
| Batch-to-batch consistency (same method) | Water, salts and counter-ions, which barely absorb at 214 nm |
| Degradation over time (repeat testing) | How many milligrams of peptide are in the vial |
The last two rows explain a common surprise: a 99% pure peptide can still contain only 70-85% peptide by weight. Water and counter-ions are effectively invisible to the UV detector, so they are left out of the purity calculation. Net peptide content is the measurement that accounts for them.
HPLC vs. mass spectrometry: why you need both
Mass spectrometry answers the question HPLC can’t: what is the main peak? It measures molecular mass, which is set by the amino acid sequence, so a match between observed and expected mass confirms identity. Combined in one instrument as LC-MS, the two techniques can also identify individual impurities. A Ghent University study showed that adding even a simple single-quad MS detector to routine HPLC lets a lab identify the main compound and smaller impurities directly.
| Test | Question it answers | Typical result on a COA |
|---|---|---|
| HPLC-UV | How pure is it? | Purity 99.1% |
| MS / LC-MS | Is it the right molecule? | Observed 1419.6 Da, expected 1419.5 Da |
| Quantity (HPLC vs. standard) | How much is in the vial? | 10.2 mg per vial |
| Amino acid analysis | Is the composition right, and how much is peptide? | Net peptide content 82% |
Rule of thumb: treat a purity result without an identity result as half a COA.
Which impurities HPLC finds in synthetic peptides
Most of what HPLC peptide testing detects comes from how peptides are made. Research peptides are made by solid-phase peptide synthesis (SPPS), adding one amino acid at a time. Each step is very efficient but not perfect, so a small fraction of chains end up slightly wrong. A detailed review of peptide impurities groups the usual suspects as:
- Deletion sequences: one amino acid missing, from an incomplete coupling step.
- Truncated sequences: chains that stopped growing early.
- Insertion sequences: an extra amino acid from excess reagent.
- Incomplete deprotection: protecting groups left on side chains.
- Oxidation and racemisation: chemically modified or mirror-image residues.
Most of these differ only slightly in hydrophobicity from the target, which is why a good method, with a shallow gradient and a decent column, matters. Waters’ synthetic peptide application note shows how much separation can change between columns and mobile phases for the same peptides.
What purity grade do you need?
HPLC peptide testing gives you a number; whether it is good enough depends on the experiment. As a general guide used across peptide suppliers:
| Purity | Typical research use |
|---|---|
| >70-85% | Antibody generation, early screening |
| >95% | Most in-vitro assays, quantitative work |
| >98% | Sensitive assays, structural and analytical studies, reference work |
All Baltic Peptides batches are released at research grade and published with their HPLC and mass spec results on our COA page; our batch average is 99.1% HPLC purity.
Comparing HPLC results between suppliers
Two results from HPLC peptide testing are only directly comparable if they were produced with similar methods. When you compare reports, check:
- Same lab or same method: column type, gradient and wavelength can shift results by a percent or two.
- Full chromatogram shown: so you can see whether small peaks were integrated or ignored.
- Independent testing: a third-party lab such as Janoshik Analytical rather than the seller’s own report.
- Batch match: the report must belong to the batch you are buying. See our COA checklist.
A supplier who publishes the chromatogram, the method and an identity result for every batch is giving you something you can actually check.
Reading the method details on an HPLC report
A good HPLC peptide testing report states the conditions it used. These lines are easy to skip, but they decide whether two results can be compared:
| Method line | Typical value | Why it matters |
|---|---|---|
| Column | C18, 4.6 x 150-250 mm, 3-5 µm | Chemistry and length set how well similar molecules separate. |
| Mobile phase | A: water + 0.1% TFA; B: acetonitrile + 0.1% TFA | TFA sharpens peaks; acetonitrile elutes the peptide. |
| Gradient | e.g. 5-65% B over 30 min | A shallower gradient separates close impurities better. |
| Flow rate | ~1 mL/min | Affects retention time and peak width. |
| Wavelength | 214 or 220 nm | Where the peptide bond absorbs, so impurities are seen too. |
| Run time | 20-40 min | Too short a run can miss late-eluting impurities. |
If a report gives none of this, you are trusting a number without knowing how it was produced.
Retention time: what it does and doesn’t tell you
In HPLC peptide testing, retention time is how long a component takes to come off the column. Under fixed conditions, the same peptide elutes at nearly the same time, so labs use it to recognise the main peak and to compare batches. But retention time is not proof of identity: different molecules can elute at the same time, and the same peptide elutes at different times on a different method. That is why identity always comes from mass spectrometry, not from retention time alone.
Peak integration: where purity numbers can be bent
Purity depends on how the software draws the baseline and which peaks it includes. Legitimate method choices can move a result slightly; questionable ones can move it a lot. Things that inflate a purity figure:
- Ignoring small peaks by setting a high detection threshold.
- Cutting the run short before late impurities elute.
- Drawing the baseline under a shoulder so it is counted as part of the main peak.
- Integrating at a wavelength where the impurities absorb poorly.
You can’t check integration settings from a PDF, which is exactly why independent testing and a visible chromatogram matter. Reports from a third-party lab remove the incentive to tune the result.
HPLC vs. UHPLC
Some labs now run HPLC peptide testing on UHPLC systems. UHPLC (ultra-high-performance liquid chromatography) uses smaller particles and higher pressure. It gives sharper peaks and shorter runs, and can resolve impurities that standard HPLC merges with the main peak. For purity reporting, both are valid; just remember that a UHPLC result can sometimes read slightly lower than an HPLC result for the same sample, because it separates more.
How Baltic Peptides batches are tested
For HPLC peptide testing and identity, every batch we release is tested by Janoshik Analytical, an independent lab in the Czech Republic, for HPLC purity and mass spec identity. The full report, with its chromatogram and task number, goes on our COA page before the batch ships. You can read more about our approach on the about page, or use our 9-step COA checklist to check any report yourself.
HPLC testing of peptide blends
Blends such as KLOW or BPC-157 + TB-500 contain more than one intended peptide, so their chromatograms show several main peaks by design. Purity for a blend is usually reported per component, or as the combined share of the intended peaks, and each component should have its own identity result. When reading a blend report, check that every listed component appears as a distinct, identified peak, and that the relative amounts are reported if the lab measured them.
Why purity can drop over time
A purity result describes the batch on the day it was tested. Peptides slowly degrade, mainly by oxidation and, in solution, deamidation and hydrolysis, and each degradation product shows up as a new small peak. That is why the test date matters, why good suppliers re-test older stock, and why storage conditions matter so much (see how to store peptides). Re-running HPLC peptide testing on an older vial is the most direct way to check it is still within specification.
HPLC testing for peptides bought in Europe
For EU researchers, independent HPLC peptide testing is easier to rely on when the whole chain stays inside the EU: the batch is tested by an EU lab, released, and shipped from an EU warehouse, so the material that was analysed is the material that arrives. Baltic Peptides ships from Lithuania with tracked delivery across the EU (see shipping), and every compound in our research peptide range, from BPC-157 to GHK-Cu, links to its current batch report.
Sources and further reading
- Bachem. Peptide purification process and methods: an overview. bachem.com
- D’Hondt M. et al. (2014). Related impurities in peptide medicines. J Pharm Biomed Anal 101:2-30. PubMed
- D’Hondt M. et al. (2016). Implementation of a single quad MS detector in routine QC analysis of peptide drugs. J Pharm Anal 6(1):24-31. PMC
- Yang H. et al. (2018). Synthetic peptide impurity analysis on Waters reversed-phase columns. Waters application note
- High-performance liquid chromatography (Wikipedia overview).
All Baltic Peptides products are supplied strictly for laboratory research use. They are not medicines, supplements or food and are not for human or animal use. This article explains analytical testing and is for educational purposes only.
FAQ
Common questions
What is HPLC peptide testing?
What does 99% HPLC purity mean?
Why is HPLC done at 214 or 220 nm?
Can HPLC confirm a peptide’s identity?
What is the difference between HPLC and LC-MS?
Why do two labs report different purity for the same peptide?
Is higher purity always better?
Where can I see HPLC results for Baltic Peptides batches?
Keep reading
Related reading
How to read a peptide COA
The 9-step checklist for any certificate of analysis.
Net peptide content explained
Why a 10 mg vial is not 10 mg of peptide, with a calculator.
How to store peptides in the lab
Keep lyophilised and reconstituted peptides stable in the lab.
See the chromatogram for every batch
HPLC and mass spec results for every compound, tested independently and published before it ships.
