Lab guide · Analytical methods
What Is HPLC? High-Performance Liquid Chromatography Explained
What is HPLC? High-performance liquid chromatography is a technique that separates the components of a liquid mixture by pushing it under pressure through a packed column, then measures each component as it emerges. This guide covers how it works, the parts of an instrument, the modes used for peptides and what a chromatogram can and cannot tell you.
Key takeaways
- HPLC separates a mixture because its components interact differently with a stationary phase inside a column while a liquid mobile phase carries them through at high pressure.
- Peptides are usually analysed by reversed-phase HPLC, which separates by hydrophobicity and detects the peptide bond by UV absorbance near 214 nm.
- A purity figure is the main peak area as a percentage of all peak areas, and it depends on the method.
- HPLC shows how much of a sample is one species. It does not show what that species is, which needs mass spectrometry.
What is HPLC?
What is HPLC? High-performance liquid chromatography separates a mixture by passing it, dissolved in a liquid called the mobile phase, through a column packed with fine particles called the stationary phase. Components that interact strongly with the packing travel slowly, and those that interact weakly emerge early. A detector records each one as a peak.
The “high-performance” part comes from the pressure. Small particles give sharp separations but resist flow, so a pump forces the liquid through the column at high pressure. For peptide work, the technique answers one question: how much of this sample is a single species, and how much is something else.
Research use only. This guide explains analytical and chemical concepts for educational purposes. Baltic Peptides supplies its compounds strictly for laboratory research; they are not medicines and are not for human or veterinary use.
The parts of an HPLC system
| Component | What it does |
|---|---|
| Mobile-phase reservoirs and pump | Deliver solvents at a controlled flow rate, often mixing them into a gradient. |
| Injector | Introduces a small, measured volume of the dissolved sample. |
| Column | Holds the stationary phase where the separation takes place. |
| Detector | Measures each component as it leaves the column, most often by UV absorbance. |
| Data system | Draws the chromatogram and integrates the peak areas. |
HPLC modes: which separation principle is used
The mode is set by the stationary phase and solvent. Reviews of peptide chromatography describe reversed-phase, ion-exchange and hydrophilic-interaction (HILIC) mechanisms, and mixed-mode setups that combine them (HPLC analysis and purification of peptides).
| Mode | Separates by | Typical peptide use |
|---|---|---|
| Reversed-phase (RP-HPLC) | Hydrophobicity | The standard for purity and purification |
| Ion-exchange | Net charge | Separating charge variants |
| HILIC | Polarity and hydrophilic partitioning | Very polar peptides that RP retains poorly |
| Size-exclusion | Molecular size | Aggregates and larger proteins |
Reversed-phase HPLC for peptides
In RP-HPLC the column is packed with non-polar particles, commonly C18-bonded silica, and the mobile phase shifts from mostly water to mostly organic solvent, usually acetonitrile, over the run. Peptides stick to the non-polar surface and come off as the organic share rises, with the most hydrophobic last. Mant, Cepeniene and Hodges (2010) showed that different RP packings give markedly different selectivity for the same peptide mixtures, which is why a second method can reveal impurities the first one hid.
The mobile phase for peptides normally contains a small amount of trifluoroacetic acid (TFA), which sharpens the peaks. That same acid is why most research peptides end up as TFA salts, explained in net peptide content.
Reading a chromatogram
The detector trace plots signal against time. Each peak is a component, its position is the retention time, and its area reflects how much of that component was present. Peptide bonds absorb strongly at wavelengths around 210-220 nm, so peptide analysis typically uses UV detection near 214 nm, where almost every peptide-like species shows up.
The purity figure is area percent: the main peak area divided by the total area of all integrated peaks, times 100. A main peak of 98.7 out of 100 area units gives 98.7%. Our guide to HPLC peptide testing walks through what a good chromatogram looks like and the mistakes to watch for.
What HPLC cannot show
- It does not prove identity. A clean single peak could be the wrong compound, so identity needs mass spectrometry.
- Area percent assumes each species absorbs equally. Residues such as tryptophan absorb more strongly than the peptide bond alone, so the figure is an approximation.
- Water and counter-ions barely absorb at 214 nm, so a 99% pure sample can still be only 70-80% peptide by weight.
- Purity depends on the method. A different column, gradient or wavelength can resolve peaks that another method merges.
- Impurities that co-elute with the main peak are invisible to a single method.
Analytical versus preparative HPLC
The same technique is used at two scales. Analytical HPLC uses small injections to measure purity. Preparative HPLC uses larger columns and loads to purify a synthetic peptide after synthesis, and the review of peptide HPLC describes preparative protocols for loads up to 200 mg on analytical columns and instrumentation (HPLC analysis and purification of peptides). Purification is the step where most TFA salt forms are created.
What HPLC looks like on a certificate
On a certificate of analysis, the HPLC section usually gives the purity percentage, the wavelength, the column and the retention time, and often shows the chromatogram itself. A real report links the trace to a batch code. The COA reading guide covers the other lines, and verifying a certificate with the lab covers authenticity.
See how to store peptides and the guide to reading a peptide COA. Batch reports are on the COA page.
Sources and further reading
- Mant C.T., Cepeniene D. and Hodges R.S. (2010). Reversed-phase HPLC of peptides: assessing column and solvent selectivity on standard, polar-embedded and polar endcapped columns. J Sep Sci 33(19):3005-3021. PubMed
- HPLC analysis and purification of peptides (methods chapter). PMC
- Reversed-phase fused-core HPLC modeling of peptides. PMC
All Baltic Peptides products are supplied strictly for laboratory research use. They are not medicines, supplements or food and are not for human or animal use. This article explains analytical and chemical concepts and is for educational purposes only.
FAQ
Common questions
What is HPLC?
What does HPLC stand for?
How does reversed-phase HPLC separate peptides?
Why is 214 nm used for peptide HPLC?
How is HPLC purity calculated?
Does HPLC prove what a peptide is?
Why do peptides carry TFA after HPLC?
Keep reading
Related reading
HPLC peptide testing explained
Purity, chromatograms and what the numbers mean.
Peptide mass spectrometry
How mass confirms identity and complements HPLC.
How to read a peptide COA
The 9-step checklist for any certificate of analysis.
Independent HPLC and mass spec data for every batch
Independent HPLC and mass spec results for every batch, dispatched from the EU.
